Main page » Turntable general » Do It Yourself

Do It Yourself

Here you will find:

Belt (Replica):
6800574NB
Sustitute for Thorens Part Number:
6800574
Used in Thorens Models (without guarantee):
TD125, TD126, TD145, TD146, TD147, TD160, TD165, TD166, TD280 (nicht TD280MKIV !), TD316, TD318, TD320, TD321, TD325, TD520, TD521, TD2001, TD3001

14,62 EUR

incl. 16% tax excl. Shipping costs

Motor Flange EDS930

Dualfred Part Number:
300091
Intent of use (refer picture 2):
With the motor flange 300091 it is easy to integrate the Dual EDS930 motor for DIY-projects.
Outside diameter =180mm
Mounting hole diameter = 170mm
The motor on picture 2 is not in the delivery content!

18,52 EUR

incl. 16% tax excl. Shipping costs

Motor Set DC200 for DIY

Dualfred Number:
300246
Description:
Motor Set for a DIY design of a turntable with belt drive. The Motor is already installed at a carrier plate by using the Dual Motor Fixture 271780. This unit uses a special rubber damper part for decoupling of the motor. The motor itself is a Dual DC200, which has an integrated contoller circuit for 33 and 45 RPM platter speed. For individual speed adjustment, the motor is equiped with a poti for each speed.

Motor speed and pulley dimension fits to a subplatter design with ~160mm diameter, which is exactly the diameter of most Thorens subplatters. So it is possible to design a turntable by using Thorens Platters and Sub Platters. You will also find a selection of sub platters, platter axles and platter bearings here in the webshop.

The electronic integration of the motor is also quite simple. You will need a 12V-DC power supply and an external switch for speed selection. A wiring diagram is included in the delivery content. But the 12V-DC power supply and the external switch is not included in the delivery content!

Pictures 2 and 3 show the important dimensions for the mechanical integration.

47,76 EUR

incl. 16% tax excl. Shipping costs

Platter Bearing 10mm cpl. Replica

Dualfred Part Number:
7646025NB
Description:
Replica of the platter bearing 7646025. The metal bearing flange is an original Thorens part. The brass bushing is a newly precision manufacured part. The important dimensions are picked from the original drawing. The big difference to the original design is the axial bearing section. The axial bearing is made from a Teflon-Graphite-Compound. It can be changes, as it is ebedded in a bearing nut. This nut is bigger in diameter (~23mm instead of ~16mm). So it might be necessary open the drill hole in the bottom plate of the turntable. The original sheet metal ring for the grounging of the bearing is already integrated.

This Platter Bearing is also a good choice for DIY turntable projects. It can be combined with platter axle 6862042 and Thorens Sub Platters.
Used in Thorens Models (without guarantee):
TD320MKII, TD320MKIII, TD321, TD520, TD2001, TD3001

96,50 EUR

incl. 16% tax excl. Shipping costs

Platter Bearing 7mm cpl. Replica

Dualfred Part Number:
7643070NB
Description:
Replica if the platter bearing 7643070, Also compatible to 7845007. The plastic bearing flange is an original Thorens part. The brass bushing is a newly, precision manufacured part from the original drawing. The axial bearing is made from a Teflon-Graphite-Compound.

This Platter Bearing is also a good choice for DIY turntable projects. It can be combined with platter axle 6845070 and Thorens Sub Platters.
Used in Thorens Models (without guarantee):
TD280MKII, TD110, TD115

57,51 EUR

incl. 16% tax excl. Shipping costs

Thrust Plate (10mm Dualfred Bearing)

Dualfred Part Number:
300176
Description:
Spare Thrust Plate for 10mm Dualfred Bearing #7646025NB
Material Teflon-Graphite Compound

8,77 EUR

incl. 16% tax excl. Shipping costs

Show 1 to 6 (from a total of 6 products)